The ruling
Only gently, and growth needs no jet. We treat Colorbond with UNGROW Bailiff at low pressure from the roofline, and it ends the growth where it sits, as on tiles. Where BlueScope allows waterblasting, for severe swarf stains, it caps pressure at 400 psi; a home pressure washer such as Kärcher's K 5 is rated to 2,300.
What the steel makers actually say
BlueScope, which makes Colorbond and Zincalume steel, sets a water pressure limit in its bulletin on severe swarf staining, the rust marks left by steel filings from cutting and drilling. For prepainted steel it says: "The affected area should be thoroughly waterblasted with clean fresh water using a pressure not exceeding 400psi (2760kPa)."1 That limit is for a stain made of loose steel particles, not for growth.
Lysaght, BlueScope's roofing brand, washes debris from around flashings and joints with a "pressure hose", and attaches a condition: "Care should be taken to ensure that debris is not lodged between sheets or the sheeting and flashing and that water from the pressure hose is not driven into the building."2 And BlueScope's maintenance bulletin asks for any cleaning method to be tested first on a small hidden section of the building, "to ensure that no damage to the steel sheeting occurs (e.g. surface dulling or discolouration)".3
Now the machine. Kärcher's K 5 Premium Power Control, a home pressure washer, is rated to a maximum of 2,300 psi.4 BlueScope's limit is under a fifth of that.
In plain terms BlueScope's limit is for rinsing loose steel crumbs off the paint. Kärcher's K 5 at full power is rated to more than five times that, which is the difference between rinsing a plate under the tap and scouring it.
Where the water goes
A steel roof is built to shed rain falling down it. The overlap between sheets is an anti-capillary lap, shaped so water runs past the joint instead of being drawn into it. BlueScope warns that if a lap is deformed enough to lose that anti-capillary effect, "water can be drawn into the lap and cause damage"5, and it tells solar installers to keep brackets away from the side laps, because they may distort the profile and let water in.6
A jet aimed up the roof turns all of that around. That is what Lysaght's condition guards against: water from the hose driven into the building, and debris lodged between the sheets or under the flashings.2 BlueScope adds that any washing must not flood the eaves, which could damage the ceilings below.6 Debris left in a joint does its own harm: BlueScope's Colorbond roof warranty does not cover corrosion due to "failure to remove debris and/or allow free drainage of water/moisture".7
In plain terms A lap is a door that only opens one way. Rain pushes on it from the right side. A jet aimed uphill pushes from the wrong one.
Pressure does not end the growth
Lichen anchors itself with threads that grow into the surface it lives on8, and on painted steel it has been found cracking the paint around itself and holding flakes of paint inside its body.9 A jet strong enough to tear that loose is working on the paint as well. The steel maker does not reach for pressure against growth. BlueScope's own method for fungus and lichen on Colorbond is a 2 percent sodium hypochlorite solution brushed on with a soft bristle broom, left for 3 to 5 minutes and rinsed off with plenty of fresh water.10 The difference between the two approaches is set out in soft wash or pressure wash.
What ends it is a treatment. We put UNGROW Bailiff on Colorbond and Zincalume at low pressure from the roofline, and it works on steel the same way it works on tiles: it ends the growth in place, and the weather carries it off over the following months, with the paint left as it was.
Growth also returns where the roof stays damp. BlueScope calls fungal growth on its steel "a natural occurrence", and says heavy growth is often seen along the ridge capping, where moisture and nutrients leave the roof cavity, with the areas around bathroom vents another such spot.10 Can moss and lichen grow on a metal roof explains why. Staying treated with UNGROW Sentry, our preventative, is what keeps it off, and on smooth painted steel, which holds less of the treatment than a porous tile, its top up can come round sooner.
In plain terms It is the difference between soaking a burnt non stick pan and taking a wire brush to it. Both shift the mess. Only one leaves the coating on the pan.
Getting the hose up there
A pressure washer on a roof means someone on the roof, on a wet surface. BlueScope says foot traffic can dent, scuff or scratch roof sheeting, that dents on low pitched roofs can pond water and raise the potential for corrosion, and that working on a wet roof is not recommended because roofs are slippery when wet.6 It asks anyone crossing a roof to wear soft soled shoes, spread their weight, and walk in the pans or over the fasteners.11 Lysaght says patio and verandah roofs are not designed for foot traffic and should not be walked on at all, and warns that warranties "may be rendered null and void if work conducted damages the roof".2 The case against anyone walking a roof at all is in why nobody needs to walk on your roof.
In plain terms The person holding the wand is standing on a wet, sloping steel sheet, leaning into the kick of the machine.
What this means for your roof
On a Colorbond or Zincalume roof, the makers cap the water pressure, aim it with care, and keep it out from under the laps and flashings. Growth on steel calls for a gentle method, not a jet, and the sooner it is dealt with, the less there is to shift. We treat Colorbond and metal roofs with UNGROW Bailiff from the roofline, the same way as tiles, applied through a low pressure soft wash pump and non-directional nozzles, so nothing is forced under the laps and nobody walks on the sheets. UNGROW Sentry, our preventative, keeps it treated after that. Run the Roof Report to see which faces of your roof stay wet longest, and put your address in below for a fixed price.
Also asked
Is it okay to pressure wash a metal roof?
Only within the steel makers' limits, and growth needs no jet. We treat metal roofs with UNGROW Bailiff at low pressure from the roofline, the same way as tiles. BlueScope's bulletin on swarf staining limits waterblasting to 400 psi. Lysaght uses a pressure hose to wash debris away, with care that water is not driven into the building or debris lodged between the sheets. Neither gives a pressure washer as the way to clear fungus or lichen. For that, BlueScope's method is a brushed on bleach wash, rinsed off.
Does pressure washing void a Colorbond warranty?
BlueScope's sample warranty for Colorbond roof sheets does not name pressure washing. It does exclude accidental or intentional damage by a person, mechanical damage after the roof goes on, and failure to remove debris or allow free drainage, and it stays effective only while the roof is maintained in strict accordance with BlueScope's technical bulletins. The bulletin on swarf staining limits waterblasting to 400 psi. Lysaght adds that warranties may be rendered void if work damages the roof.
Why is my Colorbond roof leaking?
That is a question for a roofer, on the roof. BlueScope names some causes worth knowing. Sheet overlaps deformed enough to lose their anti-capillary effect can draw water in. Dents on low pitched roofs can pond water. Brackets fixed near the side laps can distort them. Lysaght's warning about pressure hoses is the same kind of thing: water driven into the building where the roof was never meant to take it.
Can I pressure wash the gutters and downpipes?
Lysaght's manual says downpipes made from steel should be cleaned with a pressure water hose directed down each one, then the hose fed down the pipe to check it is clear. Gutters are swept out first with a soft bristle brush, never a shovel or hard tool, then rinsed. Any blockage should be cleared straight away, before water backs up into the gutters.
On the record
- BlueScope, TB-5 Swarf staining (2022)
- Lysaght (BlueScope), Roofing & Rainwater Maintenance Manual (2024)
- BlueScope, TB-4 Maintenance of exterior BlueScope coated steel products (2026)
- Kärcher Australia, Pressure washer K 5 Premium Power Control Home
- BlueScope (COLORBOND steel), Frequently Asked Questions
- BlueScope, TB-36 Guide to good practice: steel roofing and photovoltaic/solar panels (2025)
- BlueScope, COLORBOND steel when used in the manufacture of roof sheets in Australian applications (sample warranty) (2026)
- Australian National Botanic Gardens, Lichen form and structure
- Journal of Basic and Applied Research International, Lichens growing on painted metal plates (2015)
- BlueScope, TB-27: Identification of fungus in the field and recommendations for its removal (2022)
- BlueScope, CTB-17 Following trades (2022)