The ruling
Partly, and only below them. Rain carries metal from the strip down the roof, and zinc and copper ions hold back moss and algae in a band beneath it. Most zinc strips are effective for up to a year, and existing moss should be cleared first. A strip does not clear a roof. Treating the growth where it sits does.
What a zinc strip is
A zinc strip is a band of zinc, or galvanised metal, fixed along the ridge of a roof. Oregon State University's moss pages, quoted by the University of Washington's horticulture library, describe what happens next: "With each rain zinc is released from the strip," and the zinc holds back the moss below it. The active ingredient, they say, is metallic zinc.1
In plain terms It works like a tea bag at the top of the roof. Every shower draws a little out and carries it down the slope.
How metal holds growth back
The idea comes from something noticed on real roofs. A review of roof weathering from Lawrence Berkeley National Laboratory notes that in some cases staining does not occur near copper and galvanised zinc flashings, and concludes that "zinc and copper ions can inhibit biological growth".2 The same review cites patents for zinc and copper compounds on asphalt shingles and in roofing granules, to hold back the algae, cyanobacteria and fungi that stain shingle roofs.2
So the mechanism is real. Metal ions in the runoff make the strip of roof they flow over a poor place for moss, algae and fungi to establish. What matters is where that runoff goes, and how long the strip stays effective.
In plain terms You have probably seen it already. The clean stripe below an old galvanised flashing, on a roof that is dark everywhere else, is a zinc strip that nobody installed on purpose.
The band below the strip, and nowhere else
The effect only travels where the water travels: down the slope, directly below the strip. The Oregon State guidance says zinc strips "appear to have effect up to 15 feet below the zinc flashing along the length of the flashing".1 That is about 4.6 metres at most, and only along the length of the strip. Oregon State's older fact sheet gives a galvanised or copper ridge the same kind of reach: about 10 to 15 feet down from the ridge on most roofs, roughly 3 to 4.6 metres.3
That shapes what a strip can and cannot do on a real roof. It reaches the face it sits above, down to the limit of that band. It does nothing for a face it does not drain onto, for the far end of a long slope, or for the patch under a tree whose drip keeps it damp. Growth on a roof is decided by water, shade and aspect, and those do not line up neatly beneath a ridge. Why the south faces and the shaded corners grow most is in why roofs grow moss and lichen.
In plain terms A zinc strip is a sprinkler that only waters downhill. Whatever is beside it, above it or out of reach stays dry.
Prevention, not removal
A zinc strip does not clear a roof. The same guidance says "For best results remove the existing mosses prior to treatment", and that strips are "most effective before mosses are well developed".1 A strip keeps a clean surface clean. It does not clean a dirty one.
That matters, because the growth already on a roof keeps working while a strip waits for rain. Moss holds from a few times to many times its own weight in water, and traps soil and debris against the roof.4, 5 Monier, who make roof tiles, name blocked gutters, downpipes and valleys as common sources of leaks.6 A crust lichen is firmly attached to the surface by its entire underside.7 On clay roof tiles, electron microscopy found lichen threads penetrating the tiles and filling their fissures and cracks, and the researchers trace the lichen's action on the ceramic to oxalic acid, a process they link to the deterioration and ageing of the tile.8 The full case is in what moss, lichen and algae do to a roof.
The guidance on strips is written for moss, algae and fungi, and it puts the strip after the clearing: physical removal of the existing moss first, then the strip.1, 2
In plain terms A zinc strip is a fence, not a mower. It can help keep a cleared patch from filling back in. It will not cut what is already growing.
On a Perth roof
The research and guidance behind zinc strips comes from North America and is built around shingle roofs: Oregon State's moss advice is written for the Pacific Northwest, with its zinc sulfate rate set by the condition of the wood, and the metal ion work is on asphalt shingles and their granules.5, 2 A Perth tiled roof is a different job. The instruction is to fix the strip along each side of the ridge caps, with a nail down each foot of it.1 On a tiled roof the ridge capping sits on mortar bedding finished with pointing, and Monier lists cracked or broken bedding under the ridge and hip capping among the usual causes of a leak.9 Fitting a strip means working along the ridge, which is the highest and most exposed line on the roof. Why a treatment needs nobody walking the roof is in why nobody needs to walk on your roof.
On a metal roof, the steel maker decides. Lysaght's compatibility table lists copper and copper alloys draining onto Colorbond or Zincalume steel as not compatible.10 Oregon State also warns that zinc corrodes copper, so zinc sulfate should not be used where there are copper gutters, downpipes or flashing.5
In plain terms What works on a shingle roof in Oregon does not transfer neatly to concrete tiles in Perth, and on steel, the metal you add has to suit the metal that is already there.
What is the white powder people put on roofs?
Usually zinc, in a bag instead of a strip. The powder sold for spreading on roofs against moss is most often zinc sulfate: the University of Washington's horticulture library reports a City of Portland guide naming it the most common product sold for moss removal.1 Oregon State's moss pages name zinc sulfate monohydrate, usually at 99%, as the active ingredient in some moss products, applied as a powder directly onto the moss or mixed with water and sprayed.11, 5 PubChem describes zinc sulfate monohydrate as a white, odourless powder.12
It works the same way as a strip: zinc ions in the water on the roof hold back moss.2 The difference is the delivery. A strip releases a little zinc with each rain; the powder goes on in one dose, onto the patches it is spread over.1, 11 Kitchen cupboard powders and sprays are covered in vinegar, bleach and home remedies.
In plain terms A strip is a dripper that lets out a little zinc every shower, and the powder is the same zinc tipped out of a watering can in one go. Both reach only where they land and where the water carries them.
White powder that is already on a roof, and that nobody put there, is a different suspect. On concrete tiles, Monier, which makes roof tiles, describes natural salts moving to the surface as a whitish grey discolouration called efflorescence.9 How to tell that from a pale crust lichen is in what are the white spots on my roof tiles.
Where a strip fits
A zinc strip has a place: a face that has been cleared, sits fully below the strip, and is not shaded by something the strip cannot reach. Even there it works downslope only, no more than about 4.6 metres deep, and for up to a year on most brands.1
What clears a roof is dealing with the growth where it sits. We do that with UNGROW Bailiff, our treatment, mixed to the label rate and applied to every face from the roofline. It ends moss, lichen, algae and mould in place, and the weather carries them off over the following months. How that works is in how roof treatment works. Growth recurs on any roof that stays damp, strip or no strip, which is why staying treated is what resolves it. That is the job of UNGROW Sentry, our preventative: it goes on every face, not one band below the ridge. How often that needs doing is in how often does a roof need treating.
In plain terms If the roof is already green, a strip is a lock fitted after the burglary. Deal with what is there, then decide whether a strip earns its place.
What this means for your roof
A zinc strip is a fence along the top of one face: it reaches a few metres down, and on most brands it is effective for up to a year. It does not clear moss already holding water against the tiles or packed into the valleys and gutters, or lichen already anchored in the tile surface. We treat every face with Bailiff from the roofline at low pressure, mixed to the label rate and measured to the roof's area, with nobody walking the tiles, and the growth weathers off where it sits over the months that follow. Sentry then keeps the whole roof treated, not just the band below the ridge.
Also asked
How long do zinc strips last on a roof?
Oregon State University's moss guidance, as quoted by the University of Washington, says zinc strips are considered effective for up to one year for most brands, while the effect of galvanised flashing can persist for decades. The same guidance says strips and flashing work best before moss is well developed, so a strip belongs on a roof that has already been cleared.
Do copper strips work better than zinc?
Both work the same way, by releasing metal ions in the runoff, and roofing researchers note that in some cases staining does not occur near copper or galvanised flashings. Copper has a catch on a metal roof: BlueScope's Lysaght lists copper draining onto Colorbond or Zincalume steel as not compatible. On a metal roof, the steel maker's guidance comes first.
Can I use zinc sulfate to clear moss from my roof?
Oregon State University describes zinc sulfate sprayed onto a cleaned wood shingle roof in Oregon, and warns not to use it where there are copper gutters, downpipes or flashing, because zinc corrodes copper. In Australia the label decides: use a product only for the job its label names, on the surfaces it names, at the rate it gives.
Will a zinc strip clear lichen?
A strip is not built for it. The guidance on zinc strips is written for moss, algae and fungi, and even for moss it says to remove what is there before fitting one. A crust lichen is attached to the tile across its whole underside, and on clay roof tiles electron microscopy found lichen threads filling the tiles' fissures. That needs treating where it sits. A strip can only help keep a band clear afterwards.
How do you fit zinc strips to a roof?
The usual instruction is a strip along each side of the ridge caps, with a nail down each foot of it. On a tiled roof the ridge capping is set in mortar bedding and pointing, and Monier lists cracked bedding under the capping among the causes of leaks. Fitting one means working along the ridge, the highest and most exposed line on the roof. We do not give a recipe for that. Nobody needs to walk on your roof to treat it.
On the record
- Elisabeth C. Miller Library, University of Washington, On roof moss removal
- Lawrence Berkeley National Laboratory, Weathering of Roofing Materials: An Overview
- Oregon State University Extension Service, Controlling Moss on Roofs (1981)
- Australian National Botanic Gardens, Bryophyte ecology
- Oregon State University Extension Service, How to control roof moss and prevent long-term damage
- Monier, Roof cleaning and maintenance
- Australian National Botanic Gardens, What is a lichen?
- Scanning, Evaluation of the effect of lichens on ceramic roofing tiles by scanning electron microscopy and energy-dispersive spectroscopy analyses (2005)
- Monier, FAQs
- Lysaght (BlueScope), Compatibility of Materials for Direct Contact and Drainage
- Oregon State University, Chemical moss control for roofs
- PubChem, National Center for Biotechnology Information, Zinc sulfate monohydrate