The ruling
Treat it where it sits, never scrape it. We treat lichen on Colorbond with UNGROW Bailiff from the roofline, and it works as on tiles: it ends the lichen in place and the weather carries it off. Scraping takes paint with it. BlueScope's own hand method is a 2 percent bleach wash, rinsed off.
Is it lichen, fungus or dirt?
Start by knowing what is on the roof, because the steel maker treats them differently. BlueScope divides what grows on its roofs into fungus and lichen. Fungus is generally black; lichen, a fungus in partnership with an alga, shows as green and often leafy patches.1 On a Perth roof, lichen also shows as the crusty grey patches. Lichen, moss, algae or mould shows how to tell them apart by form, not colour.
BlueScope's bulletin gives a spot test. Put a drop of fresh household bleach, preferably above 3 percent, on a suspect patch, mark the edge of the drop with chalk or a coloured pencil, never a graphite pencil, and wait a few minutes. If the dark material bleaches clean, it is fungus; ordinary dirt does not bleach. BlueScope notes that algae and other organic matter also bleach, so it is not a perfect test, but it separates growth from dirt. Wear rubber gloves, because the solution is alkaline, and rinse the spot with fresh water afterwards.1
Small red brown spots with a dark centre are neither. That is usually swarf, steel filings left behind by a tradesperson and rusting on the surface, and BlueScope says those stains are often mistaken for the roof itself deteriorating.2 That is covered in does a Colorbond roof rust.
In plain terms It is the same test as dabbing a stain on a shirt collar. If it lifts with bleach, it is not dirt.
Why lichen does not just wipe off
Lichen does not sit on a surface. It anchors to it with hyphae, fine fungal threads that grow down into whatever it lives on, and the crust kinds bind so tightly that their underside cannot be seen.3 On painted steel, researchers in Argentina looked at the meeting point under the electron microscope after 15 years outdoors. The paint had cracked around a crust lichen, Caloplaca cinnabarina, and small pieces of the paint were trapped inside the lichen's body. They concluded that this lichen can deteriorate the painted surface and take up pieces of it.4
That is why scraping is the wrong tool. There is no clean line between lichen and paint to get a blade under, and BlueScope says abrasive sponges and scourers "are not suitable for use and will damage the surface of the steel product".5 Even swarf that has become stuck to the sheet is only to be detached with maximum care, BlueScope says, and never by anything likely to remove the paint or metallic coating, because any damage to these coatings "may lead to reduced life of the material".2
In plain terms Lichen on paint is like a sticker that has been on a car for fifteen years. Pick at it and the paint comes with it.
BlueScope's method, in full
BlueScope's fungus bulletin is the steel maker's own instruction for lichen and fungus on Colorbond, and Lysaght's maintenance manual sends owners to it whenever significant fungal growth is found.6 It recommends washing the roof down with a 2 percent sodium hypochlorite solution, made up from commercially available bleach. Its dilution table works it out: for a bleach at 4 percent, mix 500 mL of bleach with 500 mL of water to make a litre; at 10 percent, 200 mL of bleach with 800 mL of water.1
Then:
- Clear the loose material first. Sweep twigs, leaves and fungal matter off with a stiff, soft bristled brush, no hard tools, and hose the roof down.6
- Brush the solution on. Apply it with a soft bristle broom. A small amount of non ionic detergent, such as dishwashing liquid, may be added to help it wet the surface.1
- Three to five minutes, no more. Then wash it off "with copious amounts of fresh potable water".1
- Keep it out of the tank. "Care MUST be taken when using hypochlorite solution to avoid any solution being washed into water tanks."1 Rainwater tanks and roof treatment covers disconnecting and first flush.
In plain terms Measured like a recipe, timed like an egg, rinsed like a dinner plate.
What not to do
BlueScope draws the limits right beside the method: higher than recommended concentrations and extended contact times "may be detrimental to the long term performance of COLORBOND® steel products".1 Solvent cleaners such as turpentine, petrol, kerosene and paint thinners never go on its prepainted steel.7 Steel wool must never be used, because it breaks up into swarf itself, and acidic products must not go on Zincalume or galvanised steel.2 That rules out vinegar on Zincalume, and it is on none of BlueScope's lists for Colorbond. Vinegar is one of the home remedies people reach for first; the rest are weighed in vinegar, bleach and home remedies.
Getting to the roof needs the same care. Foot traffic can dent, scuff or scratch the sheeting, and BlueScope does not recommend working on a wet roof, because it is slippery.8 Patio and verandah roofs should not be walked on at all.6 Blasting it off is no shortcut either: can you pressure wash a Colorbond roof sets out what the steel makers allow.
In plain terms On a painted steel roof, the gentle method is the only method. Everything harder trades the lichen for the paint.
Why a bleach wash does not keep it off
BlueScope is plain about this too: fungal growth is "a natural occurrence on COLORBOND® steel", and "cleaning remains the responsibility of the owner".1 Spores keep landing, and BlueScope sees heavy growth where the conditions stay right: it is often seen along the ridge capping, where moisture and nutrients leave the roof cavity, and the areas around bathroom vents are another such spot.1 The places that grew it once are the places most likely to grow it again. The asphalt shingle makers in the United States say the same of a bleach wash on their roofs: "The effectiveness of such cleaning is only temporary, and the discoloration may recur."9 Why some roofs grow so much more than others is in can moss and lichen grow on a metal roof, and staying treated, which is what keeps it off, is in how to stop moss growing back. On steel, that top up with UNGROW Sentry can come round sooner than on tiles: smooth painted steel holds less of the treatment than a porous tile, so we keep a metal roof on its own rhythm.
In plain terms Like mowing a lawn. The cut is the job done, not the job finished.
What this means for your roof
Lichen anchors to whatever it grows on, on painted steel it has been found cracking the paint around itself, and it comes back where the roof stays damp, so the sooner it is dealt with, and the more gently, the less paint goes with it. We treat it where it sits with UNGROW Bailiff, the same way we treat tiles, from the roofline, from ladders, with a low pressure soft wash pump through non-directional nozzles: nothing is scraped, scrubbed or blasted, nothing is forced under the laps, and the weather carries the dead lichen away. UNGROW Sentry, our preventative, keeps the roof treated after that. Run the Roof Report to see which faces of your roof stay wet longest, and put your address in below for a fixed price.
Also asked
What gets rid of lichen on a Colorbond roof?
A treatment that ends it where it sits. We treat Colorbond with UNGROW Bailiff from the roofline, and the weather carries the dead lichen off over the following months, the same as on tiles. For a hand wash, BlueScope's answer is a 2 percent sodium hypochlorite solution, which is household bleach diluted to strength, brushed on with a soft broom, left for 3 to 5 minutes and rinsed off with plenty of fresh water. It warns that stronger solutions or longer contact times may be detrimental to the long term performance of Colorbond. Test on a hidden section first, and keep the runoff out of the tank.
How do you remove moss from a Colorbond roof?
We treat moss on Colorbond the same way as lichen, with UNGROW Bailiff from the roofline. By hand, Lysaght's procedure is to sweep twigs, leaves and fungal matter into a pile with a stiff, soft bristled brush, never a shovel or hard tool, lower it to the ground, then hose the roof and gutters down. Moss holds on with fine anchoring threads, so sweeping takes the cushion and can leave a film behind. Any black film or lichen left is what BlueScope's bleach wash is for. Clear the gutters last.
Can I use a roof moss product from Bunnings on Colorbond?
Read the label first, because it says which surfaces the product is for. One maker, 30 Seconds, lists steel roofs among the surfaces for its roof treatment. Used exactly to its label, a retail product works on what its label says. The difference a professional makes is measuring the roof, dosing every face at the label rate and applying it from the roofline, from ladders, instead of walking on sheeting that BlueScope says foot traffic can dent, scuff or scratch.
Will bleach fade or mark Colorbond?
At the strength and time BlueScope sets, it is the steel maker's own method. BlueScope warns that higher concentrations or longer contact may be detrimental to the long term performance of Colorbond steel, and its maintenance bulletin says to test any cleaning method on a small hidden section first, to check it does not dull or discolour the sheet. Rinse it off with plenty of fresh water every time.
On the record
- BlueScope, TB-27: Identification of fungus in the field and recommendations for its removal (2022)
- BlueScope, TB-5 Swarf staining (2022)
- Australian National Botanic Gardens, Lichen form and structure
- Journal of Basic and Applied Research International, Lichens growing on painted metal plates (2015)
- BlueScope, TB-4a Spot cleaning of exterior COLORBOND steel products (2023)
- Lysaght (BlueScope), Roofing & Rainwater Maintenance Manual (2024)
- BlueScope, TB-4 Maintenance of exterior BlueScope coated steel products (2026)
- BlueScope, TB-36 Guide to good practice: steel roofing and photovoltaic/solar panels (2025)
- Asphalt Roofing Manufacturers Association, Algae discoloration of roofs