The science

What is the best way to clean roof tiles?

The ruling

Treat it where it sits. A leave-on treatment ends the growth in place, the weather carries it off, and the tile surface is left as it was. A crust lichen anchors into the tile, so a method that tears it off takes tile with it, and Monier, the tile maker, strongly advises against pressure washers.

Remove it now, or end it where it sits

Every method on this page does one of two things. It removes the growth from the tile today, by force, by scraping or by bleaching and rinsing. Or it ends the growth where it sits and leaves the weather to take it away. A third approach, metal strips along the ridge, tries to stop growth arriving at all.

The difference matters because of how roof growth holds on. A crust lichen is attached to the surface by its entire lower surface,1 and its hyphae grow down into the material beneath and anchor it very tightly.2 On clay roof tiles aged six to ten years, electron microscopy found lichen hyphae penetrating the tiles and filling their fissures and cracks, and the same study traced the lichen's effect on the ceramic to its oxalic acid.3 Removing that crust today means removing whatever it has grown into. What lichen does to a tile while it stays is in does lichen damage roof tiles, and getting it off without taking the tile is in how do you get rid of lichen on roof tiles.

In plain terms Getting a crust lichen off a tile by force is like getting old chewing gum off a footpath with a scraper. The gum comes off, and a little of the footpath comes with it every time.

Method How it works What it does to the tile What it costs you later Who should do it
Pressure cleaning A high pressure water jet strips growth off Takes surface off with the growth A rougher surface that colours up again sooner; prohibited on asbestos cement in WA A roofer, as the first step of a restoration
Soft wash A bleach solution at low pressure, then a rinse Little force; bleach can dull or discolour some finishes Lightens algae and mould; not a lichen treatment A roof cleaner, for algae and mould staining
Biocide treatment Benzalkonium chloride ends the growth; the weather removes it Leaves the surface as it is Nothing to the tile; it clears with the weather over the months after, and a tank downpipe comes off for a few weeks Anyone, to the label; a professional for measured dose, coverage and height
Restoration and recoat Pressure clean, repair, seal and paint A new painted surface Repainted concrete tiles need redoing every five years or so A roofer
Zinc or copper strips Metal washes down the roof in the rain Nothing directly Works below the strip, best on a cleared roof; does not clear existing crust A roofer, fitted along the ridge
Scraping and brushing Physical removal A scraper takes the top of the tile with a crust Cracked tiles underfoot, and falls Light brushing only, and only after treatment
Kitchen vinegar Acid sprayed or poured on Acid attacks the cement in concrete tiles No roof label, no rate, no tested dose Nobody, on a roof

Pressure cleaning

Pressure cleaning is the fastest way to a clean looking roof, and roof tile makers advise against it in writing. Monier, which makes concrete and terracotta roof tiles, "strongly advises against the use of pressure washers for roof cleaning" because of the significant risk of tile damage from high pressure water.4 Marley, the British tile maker, says "The use of high powered jet washes is not recommended as it can damage the surface of the slate or tile, thus reducing its expected life considerably."5 Wienerberger, another tile maker, warns that the forceful spray "can damage the tile finish and strip away colour from concrete tiles".6

Coating systems use pressure cleaning differently, as preparation for paint. Dulux's data sheet for its roof membrane system calls for a high pressure water blast of a concrete roof "at a minimum of 4000 PSI to remove dirt, excess grime, lichen/moss and all other contaminants" before the roof is sealed and painted.7 That is the point. A blast strong enough to shift lichen is strong enough to take the surface it has grown into, and a restoration then paints over the result.

Two costs come later. First, a rougher tile grows more. In laboratory fouling tests on cement mortars, how fast algae colonised a surface was governed by its roughness and porosity.8 A jet that damages the finish of a concrete tile hands the next spores a rougher, more open surface than the first ones found. Second, a fragment broken off a living lichen can grow into a new lichen,1 and a fragment of moss can grow into a new plant.9 Blasting living growth off a roof scatters it.

It also means someone on the roof. Monier says walking on roofs "may result in injury, damage, or void warranties",4 and its warranty does not cover damage from "incorrect cleaning including cleaning with unsuitable chemicals or pressure".10 Does pressure washing void a roof tile warranty? sets out exactly what the warranties say. Does pressure cleaning damage roof tiles? goes further.

Asbestos cement is a different matter in law. In Western Australia, cleaning asbestos cement sheeting with pressure water or air equipment is prohibited under the Health (Asbestos) Regulations 1992 and the Work Health and Safety (General) Regulations 2022. Pressure cleaning erodes the sheeting's surface and releases asbestos fibres in a cement slurry that settles on paving, gardens, roofs and gutters on the property and next door. The dried residue is treated as friable asbestos, and cleaning it up in a work setting requires a Class A asbestos removalist.11, 12 Can you pressure clean an asbestos roof in WA? has the detail.

In plain terms Pressure cleaning a roof is like sanding a timber floor to get a stain out. It works, and the floor is thinner afterwards.

Soft washing and bleach

A soft wash swaps pressure for chemistry: a cleaning solution applied at low pressure, left for a few minutes, then rinsed off. The roofing makers' own published methods use sodium hypochlorite, the active constituent of household bleach. BlueScope's bulletin for Colorbond steel recommends washing the roof down with a 2 percent sodium hypochlorite solution applied with a soft bristle broom, left for 3 to 5 minutes and rinsed off with plenty of fresh water.13 The American asphalt shingle makers' association says a bleach and water solution lightens algae staining, and that "The effectiveness of such cleaning is only temporary, and the discoloration may recur."14

Bleach is a stain remover first. It is good on the dark films of mould: in BlueScope's spot test, a drop of bleach on fungal staining leaves a clean spot because "the dark material will be destroyed by the bleach".13 Lichen is another matter. 30 Seconds' Outdoor Cleaner contains sodium hypochlorite and is sold to remove algae, moss, mould and mildew, and lichen is not on the list. 30 Seconds answers the question directly: its Outdoor Cleaner does not treat lichen, and it sends buyers to its Spray & Walk Away instead, whose active chemicals it says "are designed to treat lichen".15

Bleach has costs of its own. 30 Seconds warns against using its cleaner on untreated metals, powder coated surfaces, high gloss paintwork and fabric "due to possible corrosive, dulling and bleaching effects".15 BlueScope warns that stronger solutions or longer contact times may be detrimental to Colorbond, and that the solution must be kept out of water tanks.13 What a jet does to steel is in can you pressure wash a Colorbond roof? A soft wash is rinsed off by design, so all of it runs to the gutters and the garden. Soft wash or pressure wash compares the two head to head.

In plain terms Bleach takes the colour out of a stain. That is not the same as getting into a crust and ending what lives in it.

Treatment, from the shelf or from a professional

A biocide treatment is the leave-on method. Benzalkonium chloride is sprayed on, soaks into the growth and ends it where it sits, and nothing is rinsed off. Rain and weather then break the dead growth down and carry it away over months. How the chemistry works is in how roof treatment works. For the tile it is the gentlest method on this page: no force, no scraping, no rinse. It asks for two things. Time, for the weather to carry the dead growth off. And if a downpipe feeds a rainwater tank, that downpipe comes off for three to four weeks and at least 6 mm of rain, as the label asks, then goes back on.16 Rainwater tanks and roof treatment walks through that step.

Conservation science backs the approach. On engraved sandstone in Italy, monitored for 54 months, biocides applied after cleaning, benzalkonium chloride among them, gave the best results through two growing seasons away from the deepest shade, and the regrowth came in mainly from the uncleaned surfaces around each treated patch.17 Growth left on one face reseeds the faces around it, which is why a roof is treated whole.

The retail treatments are on hardware store shelves, and a retail product used exactly to its label works on what its label says. The label is the place to start: it names the active, its strength and what it treats, and its directions are the ones to follow. The products are compared in Wet & Forget, 30 Seconds and Surrender.

The hard part of doing it yourself is not the chemistry. It is the roof.

  • Falls on and from ladders put 6,230 Australians in hospital in 2024-25.18
  • Half of the fatal work falls from height in the eight years to 2011 were from 3 metres or less, and falls from ladders caused more of those deaths than any other kind, followed by vehicles and then roofs.19
  • In WA, falls from height caused 27 work deaths in the ten years to 2024-25.20
  • In October 2024 a worker cleaning gutters and roof tiles at a house in WA died after falling through the fragile roof sheeting of a patio.21

The makers say the same in their own way. Monier recommends that homeowners do not attempt to clean their own roof tiles, because of the risk of falls and of damaging tiles.4 Wet & Forget tells anyone treating a roof to be "safely harnessed to your roof" and never to walk on a section just sprayed, because "it will be slippery until it is dry".22

The chemistry is not the hard part to get hold of. Yates Surrender carries 500 grams a litre of benzalkonium chloride and is labelled for the control of moss, algae, lichen and liverwort on paths, roofs and other hard surfaces,16 and Bunnings sells it online and through its special orders desk.23 What you pay a professional for is the rest: the roof measured and every face dosed at the label rate, applied from the roofline with nobody walking the tiles, the tank, gutter and valley detail handled, and someone accountable at twelve months. That is how we work. Our treatment is UNGROW Bailiff, a benzalkonium chloride treatment, and we carry it in commercial quantities with professional spray equipment. Each roof is priced from aerial imagery of the address, and Bailiff is mixed on the day to the label rate for its measured area, applied at low pressure from the roofline and kept off any solar panels. The roof is photographed on the day and checked against that photo at twelve months. Why nobody needs to walk on your roof explains the access.

In plain terms A strong bottle is on the shelf for anyone who wants one. What changes with a professional is who climbs the ladder, who does the measuring and who comes back to check.

Restoration, strips, scrapers and home remedies

Restoration and recoating. A roof restoration cleans, repairs and repaints. Dulux's specification for its membrane system replaces cracked tiles, re-beds and re-points the ridges, hips and valleys, treats moss and lichen affected areas, blasts the roof with high pressure water, then applies a sealer and at least two coats of membrane.7 It buys a new look and the repairs, and it starts a cycle. Monier says repainted concrete tiles must be redone every five years or so to keep the look, and that repainting does not make a roof any better at keeping water out. Terracotta does not need respraying, because its colour is baked into the tile when it is fired.4 The colour coat on a concrete tile is, in Monier's words, "purely decorative".24 Restoration is a roofer's call about repairs and appearance, and it is set against treatment in roof restoration or roof treatment.

Zinc and copper strips. Roof researchers have noted that in some cases staining does not occur near copper and galvanised flashings, and that zinc and copper ions appear to inhibit biological growth.25 Oregon State University's moss pages, as quoted by the University of Washington's horticultural library, say zinc strips along the ridge appear to work up to about 15 feet, or 4.5 metres, below the strip. They are most effective before mosses are well developed, work best after existing moss is removed, and last up to a year for most brands.26 That evidence is about moss on American roofs. Strips are prevention for a cleared roof, not a way to clear an established lichen crust, and fitting them means working along the ridge. Our preventative, UNGROW Sentry, keeps a cleared roof treated from the roofline, on every face rather than one band below the ridge. Do zinc strips stop roof moss? looks at them in detail.

Scraping and brushing. A crust lichen has no underside to get a blade under, because it is attached by its whole lower surface,1 so scraping it takes the top of the tile with it. Moss scrapes off more easily, but scraping means standing on the roof, and Monier warns that even walking on a tiled roof can risk damaging tiles or personal injury.4 Brushing has a place after treatment rather than instead of it. Conservators may leave treated stone untouched for several months and then lightly brush off whatever is detaching,27 and 30 Seconds says heavily contaminated areas may need brushing to remove the dead material.28

Vinegar and household bleach. Vinegar is dilute acetic acid, and acetic acid reacts with the calcium hydroxide and carbonate in cement, dissolving the paste.29 A concrete tile is made with cement, so vinegar attacks the same calcium that lichen's own acid does. Kitchen vinegar carries no label for a roof, no rate and no tested dose. Household bleach is the soft wash chemical without the method. Vinegar, bleach and home remedies covers the rest of the list.

In plain terms Vinegar on a concrete tile is an acid on a surface made with the very thing acids dissolve. It is lemon juice on a limestone step.

What a treatment does, and what a roofer does

A treatment deals with what is growing on the roof. Here is what sits alongside it.

  • Broken, cracked or slipped tiles, cracked ridge bedding, and leaks. Monier lists the usual causes of a leaking tiled roof as blocked gutters, valley gutters and downpipes, cracked bedding or pointing on the ridge and hip capping, cracked or broken tiles, displaced tiles, and debris blocking the drainage channels under the tile laps. Each has its own fix: clean it out, re-bed or re-point the capping, replace or reposition the tile.24 That is a roofer's work, alongside treating the growth.
  • A worn colour coat you want renewed. Treatment clears the growth and leaves the tile's own surface. New colour on concrete tiles is a repaint, and the five-yearly cycle that comes with it.4
  • An asbestos cement roof. An asbestos professional, first. Pressure cleaning is prohibited, as above, and we generally do not treat asbestos cement roofs. HealthyWA says many are brittle and deteriorating, and better replaced than cleaned or painted.30
  • A Colorbond or metal roof. Treated the same way as tiles. Bailiff ends the growth where it sits on steel too, and the weather carries it off, with nothing scrubbed off the paint. Can moss and lichen grow on a metal roof? has the detail.
  • A date to meet. Treatment ends the growth on the day, and the roof clears as the weather carries it off over the months that follow, so treat ahead of a sale or an event. The fast methods either take surface off with the growth, like a pressure cleaner, or lighten the colour of algae and mould without treating lichen, like a bleach wash.
  • Deep shade all year. Shade is where growth returns first: in that 54 month study, mosses and cyanobacteria came back quickly in the most shaded zone.17 So a shaded roof is one to keep treated, and trimming overhanging branches, which Monier says reduces debris and damage, also lets in light.4 Why your roof grows it explains the role of shade.

In plain terms A treatment is the gardener, not the builder. The growth is the gardener's job. A cracked tile or a leak is the roofer's.

What this means for your roof

Treating it where it sits ends the growth in place, and the weather carries it off over the following months with the surface left as it was. That matters because a crust lichen is anchored into the tile, so a method that tears it off takes some of the tile with it, and a rougher surface fouls faster. We apply Bailiff from the roofline with a low pressure soft wash pump through non-directional nozzles, so nothing is forced under the tiles or laps and nobody walks the roof. Growth recurs on any roof that stays damp, so Sentry keeps the roof treated after that.

Also asked

Is pressure cleaning bad for roof tiles?

Monier, Marley and Wienerberger, who all make roof tiles, advise against it. Monier strongly advises against pressure washers for roof cleaning because of the risk of tile damage, and Marley says a high powered jet can damage the tile surface and shorten its life. A jet strong enough to shift a crust lichen takes the surface it has grown into, and a rougher surface fouls faster. On asbestos cement roofs in Western Australia, pressure cleaning is prohibited outright.

Can I use bleach to clean lichen off my roof?

Bleach lightens algae and mould staining, but it is not a lichen treatment. 30 Seconds says its own bleach based Outdoor Cleaner does not treat lichen, and points buyers to its Spray & Walk Away instead. Bleach also has to be rinsed off, can dull or discolour some finishes, and runs into the gutters and the garden on the way down.

Do zinc strips stop moss and lichen?

For moss, as prevention. American evidence says zinc strips along the ridge appear to work up to about four and a half metres below the strip and do best on a roof that has been cleared first. They do not remove an established lichen crust, and fitting them means working along the ridge. On a roof that already has growth, the growth comes first.

Is roof restoration better than roof treatment?

They do different jobs. A restoration pressure cleans, repairs and repaints the tiles, which suits a roof that needs repairs or a new colour, and on concrete tiles the paint needs redoing every five years or so. A treatment leaves the tile surface as it is and deals only with the growth. A sound roof with growth on it needs the second.

Can I treat my own roof?

Yes, with a roof treatment from the hardware store used exactly to its label, and those products are on the shelves. The hard part is the roof: measuring it, covering every face at the label rate, and doing it without walking the tiles. Monier recommends homeowners do not clean their own roof tiles at all, because of the risk of falls and of damaging tiles.

What is the fastest way to clean a roof?

A treatment does its work on the first day: it ends the growth where it sits, within hours. What takes time is the weather carrying it off over the months after, with the tile left as it was. A pressure cleaner gets to a clean looking roof sooner, and the people who make the tiles advise against it: Monier strongly advises against pressure washers because of the risk of tile damage. A bleach soft wash is quick and lightens algae and mould, but it is not a lichen treatment.

On the record

  1. Australian National Botanic Gardens, What is a lichen?
  2. Australian National Botanic Gardens, Form and structure
  3. Scanning, Evaluation of the effect of lichens on ceramic roofing tiles by scanning electron microscopy and energy-dispersive spectroscopy analyses (2005)
  4. Monier, Roof cleaning and maintenance
  5. Marley (UK), Can I clean or jet wash my roof tiles?
  6. Wienerberger UK, How to Clean Roof Tiles
  7. Dulux, via Inspirations Paint, Dulux Acratex Roof Membrane Gloss (data sheet AUAC00047) (2024)
  8. The Science of the total environment, Bioreceptivity evaluation of cementitious materials designed to stimulate biological growth (2014)
  9. Australian National Botanic Gardens, What is a bryophyte?
  10. Monier Roofing (CSR Building Products), Warranty: Concrete Roofing Products (July 2026) (2026)
  11. WA Department of Health, Managing contamination from pressure water cleaning of asbestos cement roofs: local government authority guide
  12. WorkSafe WA, Safety alert 12/2018: high pressure water cleaning of asbestos cement prohibited
  13. BlueScope, TB-27: Identification of fungus in the field and recommendations for its removal (2022)
  14. Asphalt Roofing Manufacturers Association, Algae discoloration of roofs
  15. 30 Seconds Australia, Outdoor Cleaner
  16. Yates / Hortag, Surrender Mosskiller label (10 L)
  17. The Science of the total environment, Lithobiontic recolonization following cleaning and preservative treatments on the rock engravings of Valle Camonica, Italy: A 54-months monitoring (2023)
  18. Australian Institute of Health and Welfare, Injury in Australia: Falls (2026)
  19. Safe Work Australia, Work-related injuries and fatalities involving a fall from height, Australia (2013)
  20. WorkSafe WA, State of the work environment: work-related traumatic injury fatalities in Western Australia, 2015-16 to 2024-25 (2026)
  21. WorkSafe WA, Health and Safety Bulletin No. 17: Falls through fragile roofs and roof openings (2024)
  22. Wet & Forget Australia, Lichen or black mould on your roof?
  23. Bunnings, Yates 10L Surrender Moss Killer
  24. Monier, FAQs
  25. Lawrence Berkeley National Laboratory, Weathering of Roofing Materials: An Overview
  26. Elisabeth C. Miller Library, University of Washington Botanic Gardens, on roof moss removal
  27. Microorganisms, The Control of Cultural Heritage Microbial Deterioration (2020)
  28. 30 Seconds Australia, Roof Treatment
  29. Materials Science, Effect of Limestone Powder on Acid Attack Characteristics of Cement Pastes (2014)
  30. HealthyWA (WA Department of Health), Asbestos in and around the home

Get a price

Start with the address.

We price it off the address. No site visit, no two hour window, nobody walking through your house.

  1. 01You send the address.
  2. 02We look at the roof and send you a fixed price.
  3. 03To go ahead, tap Accept on the quote. We call you to pick a day.
  4. 04We treat it and photograph it the same day.
  5. 05We check it against that photo at twelve months.
  • Fixed price
  • Fully insured
  • 12 month guarantee

NOTICE TO VACATE

To

Moss, lichen, algae, mould

Leave by

Over the next 3 to 18 months

Evicted from the roofline.

Roof treatment · Western Australia